Release when the engine starts. To stop the engine, turn the key to the left having first switched off both the cutter and Power Take-off. To prevent unauthorised use, always remove the key after use. This choke should be used in conjunction with a fast throttle setting when starting the engine from cold. It should be cancelled as soon as possible. Do not use the choke when starting a warm engine. On some models the choke control is above the fast setting, a cold engine is started on the Choke setting, a warm one on the FAST setting.
The Choke setting should be cancelled as soon as possible. The engine should be operated on the FAST setting at all times. The hour meter only operates whilst the engine is actually running. We recommend that your garden tractor is serviced after 50 hours of use or yearly, whichever comes first. This will be reset by your dealer. Note: 50 hours of mowing at 5 mph equates to miles of grass cutting! This feature should be used when the cutter deck is engaged and in conjunction with the forward speed.
To ensure complete cutting and collection the engine speed should not be allowed to fall below rpm, the display will flash should this happen.
If, when in use, the display does flash and the engine speed drops below rpm, there are two options: a Reduce forward speed b Raise the cutting height. Its function is similar to that of a car accelerator except that it controls the hydrostatic transmission and does not affect the speed of the engine.
As with the forward pedal, the speed of reversing is increased as the pedal is pushed further. For smooth braking release either pedal gradually, for an emergency stop remove foot rapidly. When you turn off the engine, the natural braking of the hydrostatic system will add to the effect of the brake. Lever C Figure 7 Neutral Valve Figure 8 The natural braking of hydrostatic transmission means that it is not possible to easily push or freewheel the tractor.
To disengage, first make certain that the machine is on a flat even surface. Locate the C Series Neutral Valve, situated alongside the rear right wheel or the A Series, alongside the rear left wheel. Disengage by pulling out the lever. You will now be able to push the tractor at a speed not exceeding 2 mph. The differential lock should only be used in situations where one wheel is slipping and the other is not. A pedal to the right of the console controls the brake and clutch.
To switch the cutter on, push the switch and then release it, this will engage the cutter deck. To stop the Cutter Deck, push the switch again. Although the Cutter Deck is automatically switched off when the engine is stopped or when the operator gets off the seat, it is not good practice to rely on these features, the Cutter Deck should always be switched OFF as soon as you have finished cutting and certainly BEFORE stopping the engine or getting off the tractor.
The Cutter will only work whilst the operator is sat on the seat. This is set to an angle of 25 degrees at the factory. If this angle is exceeded then the display will flash and a warning siren will sound. Release the footpedal, the Park Brake should then be locked in position. Figure 54 The exceptional traction of 4WD will allow you to cut in very slippery conditions, and it also allows the tractor to ascend very steep slopes.
As all terrains and conditions vary, great care should be maintained when operating the tractor. DO NOT take the tractor into an area where it could become unstable. B C A Figure 11 On no account should slopes steeper than be driven on. The PTO lever is pushed down and to the right into its locator to disengage.
There are 10 possible cutting heights, which are represented by numbers with 1 being LOW. We recommend that positions 3 or 4 are used for mowing lawns and 8 or 9 for very long grass and paddocks. When mowing in wet conditions it is advisable to select a slightly higher cutting position than would normally be used.
The height indicator on the electronic display Figure 11 - A shows the deck position 0-lowest to 9-highest. To get the best from this refinement use it to continuously adjust cutting height to suit ground and grass conditions. Figure 14 Using the lever figure 16 raise or lower the Powered Grass Collector to either the Transport position or the Collecting position. To engage the PTO drive, the PTO lever is lifted up and out of its locator and then moved to the left and released to find its own height.
To disengage the PTO pull the lever up and to the right. Using the lever figure 16 raise or lower the Powered Grass Collector. Turn the headlights OFF by pressing the rocker switch again. The headlights will not operate without the ignition switch turned on. When removing the net, we suggest you employ the assistance of another person. Disconnect opening rod by pulling back on sprung locking tube and uncoupling from pin.
Repeat other side. Undo net locking clip both sides , unhook levers from locating pins. With one person standing each side of the collector net, slide the net off the locating arms. Reverse operation for fitting. Lift the seat and the PTO flap so that both are resting in the upright position.
Always ensure the seat is latched back into position before driving off. The natural braking of hydrostatic means that it is not possible to push or freewheel the C Series tractor with the hydrostatic engaged. Locate the Dump Valve, situated along side the rear right wheel and pull it out.
You will now be able to push the tractor at a speed not exceeding 2mph. Mulching can save time, avoids gathering piles of rotting cuttings and feeds your lawn. It is however necessary to observe certain rules to mulch mow successfully. If the grass has grown long, make several passes to achieve the cut height you require.
Short clippings of 25mm 1" or less decompose more quickly. The Countax Mulcher Cutting Deck has three mulching compartments. The grass cuttings are lifted and held until they are cut several times and injected back into the turf as small particles. These release nutrients back into the soil. These diagrams are for guidance purposes only and Countax recommends that the replacement of Cutter Deck drive belts be carried out by your local Countax Dealer.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Replace faulty silencers. Do not carry passengers.
Figure 2 illustrates the panel of a C Series HE model, some models may differ in the appearance of the indicator layout - but each symbol is described below. Dashboard Indicators P Fig 2. CM - Fig 3b If your tractor is fitted with a manual transmission, the forward speeds and reverse are controlled manually via a control lever to the right of the driver. Mulching Process Illustration. You can only view or download manuals with. Sign Up and get 5 for free.
Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need. The cookies is used to store the user consent for the cookies in the category "Necessary". The cookie is used to store the user consent for the cookies in the category "Other.
The cookie is used to store the user consent for the cookies in the category "Performance". It does not store any personal data. Functional Functional. Functional cookies help to perform certain functionalities like sharing the content of the website on social media platforms, collect feedbacks, and other third-party features.
Performance Performance. Performance cookies are used to understand and analyze the key performance indexes of the website which helps in delivering a better user experience for the visitors. Analytics Analytics. Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics the number of visitors, bounce rate, traffic source, etc.
That the Brush Height Adjustment Lever is not set too high or too low fig That there is not a build up of congealed grass on the leading edge of the Brush Guard. That the Brush is not clogged.
That the Collector Belt is not slipping, if so then adjust the tension or replace the worn or damaged belt. That the Collector net is not clogged.
0コメント